Modeling and realization of real time electronic countermeasure simulation system based on SystemVue

In this paper, we proposed a new design scheme of real time electronic countermeasure simulation system. This paper mainly expounds the modeling and realization methods of each part of the whole simulation system, and the real-time property of system has been lucubrated. Electronic countermeasure simulation system is the key part of military training of individuals; it can also allow the realistic evaluation of the performance of modern equipments and techniques. As a proof, we have drawn up a series of simulation scenarios, such as radar electronic reconnaissance simulation scenario, to explain the feasibility and the superiority of our modeling scheme in this paper.     

激光制备高附着性能的铜基类金刚石膜

提升类金刚石(Diamond-Like Carbon, DLC)膜在被保护基底上的附着能力具有明显的实际应用价值。从微观机理上分析了前期设计的Cu基多层DLC膜有效性的原因。在此基础上,研究了DLC/SiC循环层中两者厚度比例对膜层的附着性能、纳米硬度和耐磨性的影响,以优化结构、进一步提升实际应用所需的膜层性能。纳米划痕和压痕测试结果表明:随着DLC层与SiC层厚度比例的增大,多层DLC膜在Cu基上附着性能逐渐降低,但当厚度比小于2.3时,仍接近厚度400 nm的单层DLC膜在Si基上的附着性能；Cu基多层DLC膜的纳米硬度逐渐提高,同时,耐磨性接近纯DLC膜。     

国防知识产权运营市场化研究

提高国防知识产权转化应用水平,关键是解决制约国防知识产权转化应用的体制机制问题。可借鉴普通知识产权运营经验,以市场化方式促进国防知识产权运营工作。针对当前运营中出现的市场失灵现象,从创新政府治理模式、引入市场机制、增强法律法规建设、搭建公共服务平台等途径入手,逐步理顺政府与市场的关系,进行国防知识产权运营市场化改革。     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.